Search results for "POWER ELECTRONICS"
showing 10 items of 80 documents
SIC based solid state protections switches for space applications
2017
Development and technology maturation of Silicon Carbide (SiC) power transistors over the last 15 years has motivated its study in aerospace systems. When compared with Si devices, superior voltage blocking capacity and the capability of operation at higher temperatures, give important advantages in space power electronics applications, similar to what happens in terrestrial electronics. This paper discusses the use of SiC power transistors for Solid State Power Switches especially addressed to the space segment. Two applications will be covered, the first is the Solid State Shunt Switch, widely used in high power Direct Energy Transfer (DET) photovoltaic power regulators and the second is …
Fuel cell modelling for power supply systems design
2008
Today academic and industrial research is addressed on fuel cell based power supply to replace current lithium-ion and similar rechargeable battery systems. For system simulation, fuel cell models are developed. Even if power electronics designers demand for a blackbox model to limit the knowledge of physical and chemical parameters, high performance in terms of model accuracy and portability is absolutely necessary. A steady state and dynamic fuel cell model oriented to power supply systems design is proposed and, as an example, the implementation on PSIM software is presented. Simulation and experimental results are compared and the model portability is discussed. ©2008 IEEE.
Adapting power consumption to performance requirements in a MSP430 microcontroller
2005
Microcontroller based low power systems using batteries must run at low clock frequencies with short activity periods to extend battery life. These constraints reduce the microcontroller computational capabilities and limit the complexity of algorithms that can be used. New microcontroller architectures, as the Texas Instruments MSP430 family, allow to adapt power consumption to application performance requirements combining several low power modes with the capability of switching the clock frequency dynamically. A complete characterization of power consumption vs. performance has been obtained for the MSP430. A method to determine the range of clock frequencies that meets a consumption and…
An efficient wireless power transfer prototype for electrical vehicles
2017
Based on the inductive power transfer (IPT), the contactless approach allows safe and comfortable operations of battery charging for Electric Vehicles (EVs). In this paper, a contactless system particularly suitable for E-bike battery charging is proposed. A practical realization of the system has been carried out, aiming at the system evaluation in terms of working and efficiency. Through a phase shift modulation, a power regulation has been implemented. The target power level is 100 W.
Experimental test on a Contactless Power Transfer system
2014
Contactless Power Transfer (CPT) is an ever-growing technology in automotive market, due to the significant improvement brought by it to battery charging operation in terms of safety and comfort. CPT is based on inductive coupling between two coils, so that power cords can be avoided for vehicles battery charging and an important contribution towards a smarter mobility can arise. In this paper, a CPT prototype for E-bike is proposed. Magnetic design and power electronics system are described. Experimental results deriving from laboratory tests are presented and power efficiency of the system is addressed.
A stacked interleaved DC-DC buck converter for proton exchange membrane electrolyzer applications: Design and experimental validation
2019
Abstract Since the two last decades, hydrogen production has been attracting the attention of the scientific community thanks to its inherent very low pollution when energy coming from renewable energy sources (RESs) are used. However, it implies the use of DC/DC converters to interface source and load. These conversion systems must meet several requirements from current ripple point of view, energy efficiency, and performance to preserve the sustainability of hydrogen production. This article proposes the design and realization of a stacked interleaved buck converter to supply a proton exchange membrane electrolyzer. The converter is designed to ensure a low output current ripple and a sui…
MATLAB Co-Simulation Tools for Power Supply Systems Design
2011
ion level. Circuit simulation software as Powersim PSIM and Orcad Pspice are the most common choice for circuit modelling. In (Basso, 2008), the design and simulation of switchmode power supplies is deeply analyzed and simulation tips in several environments are proposed. ASIC simulation and verification tools as Xilinx ISE/Modelsim or Aldec ActiveHDL are available to implement the digital controller by the VHDL or VERILOG source code. Since the interaction between subsystems is the most common source of faults, testing separately analog and digital subsystems by the means of different verification tools is a severe mistake. Matlab is a powerful simulation environment for mixed-mode systems…
Comparison between 3-ph and 6-ph PMSM drives for the electric propulsion of unmanned aerial vehicles
2021
The full electric aircraft concept requires accurate design and suitable choice and integration of all the used components. Obviously, the electric propulsion drive is one of the most important on-board equipment. Both power converters and electric motors must have low weight, suitable overload capacity and high reliability. In this paper, two possible solutions of electric propulsion motor for unmanned aerial vehicle are investigated. Sizes, weight and some features of a three-phase PMSM motor are compared to those of a six-phase motor obtained by an appropriate rewinding of the armature, with fixed stator and rotor magnetic circuits. The losses obtained from the numerical analyzes are com…
Optimal energy management in the smart grid
2017
The Smart Grid is a modern electricity grid allowing for distributed, renewable intermittent generation, partly owned by consumers. This requires advanced control and communication technologies in order to provide high quality power supply and secure generation, transmission and distribution. This book outlines these emerging technologies. Topics covered include an introduction to smart grid architecture; smart grid communications and standards; measurement and sensing devices for smart grids; smart transmission and wide area monitoring system; bad data detection in smart grids; optimal energy management in smart grids; communication and control for the smart grid; smart consumer systems; i…
A Low-Power Fully-Mosfet Voltage Reference Generator for 90 nm CMOS Technology
2006
An integrated voltage reference generator, designed for being incorporated in standard 90-nm CMOS technology flash memories, is described in this paper. A fully MOSFET based approach, using also subthreshold operated devices, has been adopted in order to achieve low-voltage and low-power requirements and to overcome the difficulties of conventional band-gap reference circuits. The proposed circuit, based on current signals, internally generates two currents with opposite dependence on temperature. The two currents are added, thus canceling almost completely temperature dependence, and then linearly converted into the output voltage. For a temperature variation between -20degC and 90degC, th…